When you are designing a piece of audio equipment, one of your major concerns is how you get to regulate or control its volume. In this case, a potentiometer which is a variable resistor may be used for specific adjustments. The device used in this situation helps you gain controls for any variable.
With an understanding of how circuitry and an equation works, you can make use of a device that could help regulate the voltage amount of the audio equipment or other electronics. A voltage divider is a passive type of line that produces an output value. This value is the lowered amount of initial voltage.
The Ohms law is used to understand the result of this device. It states that current flowing in a conductor is proportional to the difference between its ends. Meaning, if the current is reduced, then the Volt is also reduced.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
You can also create your own device if you wish to but you have to be mindful that when creating your portable gear. Most simple electronics can only withstand 5V, however, most sources like for example your remote control, a standard 9V battery will do. To do so, first, you should prepare the specific tools needed such as your leads, resistors, your battery, three alligator clamps, connectors and your voltmeter.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Over the twisted leads, ensure a solid twist by clamping the last alligator clamp on it. Then using another connector, place the red wire on the positive terminal of the battery and place the black one in the negative terminal. Hold similar charges together of positives and negatives of your voltmeter lead and clamps and turn your meters on.
The new positive terminal. After having a new set up for your circuit, the positive terminal will now be the connector which is attached to the twisted part of the resistors. However, the negative terminal remains the same. Using the Ohms law, you will understand how a 10 ohm resistor and a 20 ohm resistor with a 9V energy source will now have a new output charge of 3V.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
With an understanding of how circuitry and an equation works, you can make use of a device that could help regulate the voltage amount of the audio equipment or other electronics. A voltage divider is a passive type of line that produces an output value. This value is the lowered amount of initial voltage.
The Ohms law is used to understand the result of this device. It states that current flowing in a conductor is proportional to the difference between its ends. Meaning, if the current is reduced, then the Volt is also reduced.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
You can also create your own device if you wish to but you have to be mindful that when creating your portable gear. Most simple electronics can only withstand 5V, however, most sources like for example your remote control, a standard 9V battery will do. To do so, first, you should prepare the specific tools needed such as your leads, resistors, your battery, three alligator clamps, connectors and your voltmeter.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Over the twisted leads, ensure a solid twist by clamping the last alligator clamp on it. Then using another connector, place the red wire on the positive terminal of the battery and place the black one in the negative terminal. Hold similar charges together of positives and negatives of your voltmeter lead and clamps and turn your meters on.
The new positive terminal. After having a new set up for your circuit, the positive terminal will now be the connector which is attached to the twisted part of the resistors. However, the negative terminal remains the same. Using the Ohms law, you will understand how a 10 ohm resistor and a 20 ohm resistor with a 9V energy source will now have a new output charge of 3V.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment